Низьконавантажувач

Fliegl DTS 300 mit Radmulden

Additional Information
Low-loader chassis
Steel welded construction
Turntable with robust bearing ring
Rear support, foldable
2 outrigger plates with holder
Aluminum side impact protection
Splash flaps at the rear, covering the entire width
Partial fender in front of the 1st axle
1st pair of wheel recesses recessed in the low-bed area after the crank, sloped for access, length at the bottom approx. 1600 mm, approx. 400 mm deep. Note! Frame in the main beam area is 400 mm higher than the wheel recess.
2nd pair of wheel recesses between the axles, recessed in the low-bed area, sloped for access, length at the bottom approx. 600 mm, approx. 300 mm deep. Note! Frame in the main beam area is 300 mm higher than the wheel recess.
Extensions extendable to 3,000 mm (not in rear slope)
(However, the track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm)
Extensions extendable to 3,000 mm, also in the wheel recesses at the bottom, foldable at the wheel recess extensions (extension not in rear slope)
(However, the track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm)
Wooden boards 70 mm for extension to 3000 mm
Tie-down points for low-loader
Kljdpfx Acsi Ri Rvezju
1 pair of tie-down points recessed in the front longitudinal beam, 10 tons each
4 pairs of tie-down points in the outer frame, 5 tons each (for lashing straps)
7 pairs of tie-down anchor points recessed on the top and side in the outer frame, 10 tons each
1 x at the front on the crank
6 x in the low-bed
first tie-down point 250 mm from the front and last maximum 250 mm from the rear, distance between tie-down points no greater than 1100 mm
Coupling system for low-loader turntable
Drawbar with tested 40 mm drawbar eye
Axles + Suspension
SAF drum brake axles
Axle/suspension laser-aligned to reduce tire wear and fuel consumption
Parabolic suspension with maintenance-free steel-rubber bearing
Wheels and tires
235 / 75 R 17.5
as chosen by the manufacturer
Steel rims in twin arrangement, factory silver
Braking system
2-line pneumatic braking system
Spring parking brake
2 fail-safe coupling heads at the front, with connecting lines to the tractor unit, ABS and ALB, with ABS plug at the front, with connecting cable. Note: The trailer may only be pulled by towing vehicles that guarantee the effectiveness of the ABS!
Electrical system
24 volts, multi-chamber lights, yellow LED lighting on the side, 2 white position lights at the front
2 white/red outline lights at the rear
2 x 7-pole fail-safe plugs at the front, with connecting cable,
1 LED rotating beacon with holder, switched via parking lights (beacon removable)
2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm
Floor
Crank at the front with steel/diamond plate covering
Storage box recessed in the ramp to the crank, followed by 70 mm soft wood floor, in the wheel arch area steel/diamond plate covering
Rear slope with 70 mm soft wood floor
Low-loader platform including rear slope 6500 mm
Ramps
Steel ramps 2,800 mm long, 750 mm wide, laterally adjustable
covered with wood
with spring-assisted support
Operating instructions
With 10,000 kg axle load, an exemption permit is required, only indivisible loads are possible!!!
The specified total weight is technically possible; depending on the load, the total weight may not be reached while complying with the permissible axle/support and saddle loads. (Poor driving an

Оголошення було перекладено автоматично. Можливі помилки перекладу.