Причіп з робочою платформою

MÜLLER-MITTELTAL 5 achs Tieflader, Nachlauflenkachse, MA liftbar

T5 Profile 50.0:

----Brakes:

* Wabco EBS (Electronic Braking System)
* Emergency release device for spring brake cylinders
* Drum brakes

----Axles:

* 5 x 11 t Gigant axles
* 3rd axle liftable (when lifted, driving height +30 mm)
* Last axle self-steering (lockable from driver’s cab for maneuvering without truck-side installation, additionally switchable from the trailer); lock must be disengaged before entering public roads
* Forced lifting and lowering of the lift axle for maneuvering (truck-side installation required), speed-dependent control via EBS electronics

----Suspension:

* Air suspension, lifting and lowering system with RtR valve

----Drawbar:

* Drawbar 1,500 mm long with 50 mm towing eye and manual height adjustment

----Electrics / Lighting:

* Smartboard as infotool with pressure sensors for total axle load display per axle group
* Tire pressure monitoring with display option in truck via EBS signal (no truck-side installation required)
* LED lighting system 12 / 24 V
* LED rotating beacon (removable) at rear

----General Attachments:

* Mechanical warning board set for 3 m total width
* Toolbox made of galvanized sheet steel approx. 650 x 300 x 600 mm, mounted on left side
* Plastic mudguards front axle, galvanized steel mud flaps rear axle

----Low loader deck:

* Turntable platform with 45° corners and 3 storage compartments with lockable hinged lids (lids open to the rear)
* Low deck shortened by 500 mm to 6,280 mm including extended offset bend of 500 mm to the front
* Rubber covering on folding frame, drive-on incline, and on the running surface of the low loader platform
* Bamboo wood between the longitudinal members in front of the excavator stick storage

----Load securing (cargo securing package):

* 2 x 6.4 t lashing eyes in the front corners
* Side front and rear, 2 x 13.4 t UVV lashing points each
* 5 x 10 t UVV lashing rings per side (swiveling and retractable, loadable in all directions)
* 4 stake pockets per side, each with 2 t lashing option
* 1 x 16 t UVV lashing point on the rear crossmember

----Widening:

* Extendable and foldable extension arms for 3 m total width (timber support bracket under chassis, right side)

----Excavator Stick Rack:

* Continuous excavator stick rack with reinforcement profile from last axle to end beam, approx. L=2,350 x W=770 x H=270 mm, 2 pairs of 6.4 t UVV lashing rings on the sides

Cgedpsxptn Dofx Ah Sjp
----Ramps:

* Hydraulic folding ramps with dual-circuit hydraulics and extendable tip section, approx. 4,650 x 720 mm including load-holding valves and hydraulic side-shift

----Rear support:

* Hydraulic rear support

----Hydraulics:

* Hydraulic flow divider (for hydraulic pump capacity on the truck of over 40 l/min up to max 140 l/min)

----Loading height:

* Loaded: 890 mm +/- 20 mm via air suspension

----Platform dimensions:

* Deck above turntable: 2,600 + 390 x 2,520 mm
* Low-bed platform: 6,280 + 500 x 2,520 mm including 860 mm drive-on incline

----Paintwork:

* Chassis, turntable, drawbar, extension consoles, drive-on ramps hot-dip galvanized
* Drawbar, axles, hydraulic axle supports, and air tanks painted in a shade of black

----Information:

* New vehicle with manufacturer's warranty
* Subject to errors and prior sale

----Delivery time:

Available from calendar week

Оголошення було перекладено автоматично. Можливі помилки перекладу.